hammer vs subterrâneo
- Construction For foundations, pilings, and site preparation, DTH techniques enable precise hole placement and stability in challenging geological conditions.
(1) If the horizontal slurry pump causes a blockage of solid hard deposits in the volute, measures can be taken to remove the blockage.
(2) If the shaft is different from the stuffing box axis, it is mainly due to processing errors and incorrect installation. Then pay attention to check whether the installation is correct after installation. If the sealing water ring is badly worn, a new water ring needs to be replaced. If the sealing water pipe is blocked, the sealing water cannot enter the middle of the packing, resulting in rapid wear of the packing, resulting in material leakage, you should dredge the blocked water pipe and keep the sealing water clean.
(3) If the impeller or the inlet and outlet water pipe is blocked, the impeller or pipe can be cleaned, and if the impeller is seriously worn, it should be replaced. If the filler mouth leaks, press the filler. If the conveying height is too high or the tube loss resistance is too large, the conveying height should be reduced or the resistance reduced.
(1) If the horizontal slurry pump causes a blockage of solid hard deposits in the volute, measures can be taken to remove the blockage.
(2) If the shaft is different from the stuffing box axis, it is mainly due to processing errors and incorrect installation. Then pay attention to check whether the installation is correct after installation. If the sealing water ring is badly worn, a new water ring needs to be replaced. If the sealing water pipe is blocked, the sealing water cannot enter the middle of the packing, resulting in rapid wear of the packing, resulting in material leakage, you should dredge the blocked water pipe and keep the sealing water clean.
(3) If the impeller or the inlet and outlet water pipe is blocked, the impeller or pipe can be cleaned, and if the impeller is seriously worn, it should be replaced. If the filler mouth leaks, press the filler. If the conveying height is too high or the tube loss resistance is too large, the conveying height should be reduced or the resistance reduced.
Submarine hammer drilling, often referred to as underwater percussion drilling, is an advanced technique utilized primarily in marine construction and resource exploration. This method combines the principles of traditional drilling with hydraulic and pneumatic operations, enabling the effective penetration of hard substrates beneath the sea floor. In this article, we will explore the processes, equipment, advantages, and applications of submarine hammer drilling.
Uchinchidan, burg'ulash vositalarining narxi bozordagi talab va taklifga ham bog'liq. Agar ma'lum bir burg'ulash vositasiga talab oshsa, uning narxi ham oshishi mumkin. Bu, ayniqsa, muayyan mintaqada yoki hududda resurslar izlashga bo'lgan talab kuchaysa, ya'ni mineral resurslarning qidiruvi kuchaysa, kuzatiladi.
prix de l'engin de forage

Submarine Hammer Drilling An Insight into Techniques and Applications
Before use, check the mechanical structure and the hydraulic system, as well as the water level in the diesel engine's water tank and the motor oil level. If everything is normal, you can start the diesel engine. After running at a low speed without load for 3-5 minutes, you can begin work.
2. سهولة النقل تتميز الضواغط المحمولة بخفة وزنها وحجمها الصغير، مما يسهل نقلها من موقع لآخر. هذه الميزة تجعلها مثالية للاستخدام في مواقع العمل المتغيرة مثل مواقع البناء أو المشاريع الميدانية.
Shunga qaramay, to'g'ri burg'ulash vositasini tanlash va uning narxini aniqlashda har bir ishlab chiqaruvchi o'z ehtiyojlariga va budjetiga mos variantni izlaydi. Masalan, yirik korxonalar ko'pincha yuqori sifatli va narxli asboblarga sarmoya kiritsa, kichik bizneslar va shaxsiy foydalanuvchilar ko'proq iqtisodiy variantlarga e'tibor berishadi.
The reason:
The suction pipe is not filled with water
Blocked suction line or inadequate valve opening
The inlet pipe of the pump, the meter or the stuffing box are serious
The suction pipe is not filled with water
Blocked suction line or inadequate valve opening
The inlet pipe of the pump, the meter or the stuffing box are serious