Now it is more used in the binding of the construction industry. Compared with ordinary wire, it is also softer and has better luster. Use in daily life does not need to carry out maintenance and maintenance, saving a lot of time, but also save the cost of maintenance and maintenance. Annealed wire has good stability, good corrosion resistance, greatly prolonging the service life. There are many kinds, which can be selected according to different uses. The device for making annealed wire is simple, and the utilization rate of the device is improved. The material properties of annealed wire can meet different processing needs.

Cold drawing wire is a metal cold processing, with wire rod as raw material, that is, the mouth of the steel bar. Cold drawing wire is a product produced by a series of processes such as shell stripping, which is a common wire. In the development and production of metal materials, cold drawing wire is a very common material, its performance is good, the range of use is very wide, manufacturers in processing are the use of cold processing to produce.

A pet carrier can be used as an indoor or outdoor pet house. The dog cage is equipped with a fixed food basin and water fountain, and the foot plate pet cage rubber pad has bayonets on four sides to be splintered. It can be spliced, cut and disassembled according to the size of the cage. It is convenient and easy to clean. It can solve the problem of pinching the feet of the puppies in the ordinary cage and prevent the puppies from causing adverse reactions in the development. The dividers are breathable and comfortable, and can be used as heat shields for pets in summer. A puppy with small feet, no feet, no pinching.

Stainless steel blade barbed rope production process is basically similar to galvanized blade barbed rope production process, usually according to the mold to determine the size of the blade.

The technical term “galvanizing” means that the metal has been specially treated with zinc. Essentially, it’s wire covered with a very thin layer of zinc. It is because of this thin layer of zinc that galvanized wire has many characteristics. Zinc can be galvanized by dipping the wire into a zinc bath or by electroplating.

Removal of surface-active substances by activated carbon matting. Or make the bubble unstable according to overworry, these are all reasonable countermeasures; Other strategies should also be used to minimize the amount of surfactant taken in. The introduction of organic matter can make the electroplating process speed drop sharply. Galvanized iron wire blackening can be effectively prevented, such as: the work site to keep dry, reduce and do not use chemicals, operators with clean gloves and so on. In addition, hot dipping zinc factory can be required, after dipping zinc must be passivation treatment, passivation treatment of zinc has a better anti-discoloration effect, can effectively prolong the discoloration time, the combination of the two, discoloration should be able to solve.

It is precisely because of the advantages of electric welding mesh (explanation: can overwhelm the favorable situation of the other side), the electric welding mesh in the market is widely used in urban roads, real estate, development zones, residential areas, gardens and all kinds of enterprises and institutions of decoration beautification and security protection works. Stainless steel wire mesh is one of stainless steel wire mesh products.

This process has no mold, low processing cost, easy forming, can process a variety of shapes and other characteristics are widely used. But the products of the guardrail are powder impregnated plastic. According to whether it needs heating, it is divided into hot dipping and cold dipping. According to the raw materials of dipping, it can be divided into liquid dipping and powder dipping. Hot-dip galvanizing, as a metal anticorrosion method, is usually to put the steel structure to be derusted into the zinc liquid at about 500℃, so that the zinc layer is attached to the surface of the steel structure.

Nestor rolling cage, high-speed railway Nestor rolling cage and railway Nestor rolling cage are all produced, sold and installed in accordance with the technical requirements of the reference drawing of railway line 2012-8001. Nestor rolling cage is a kind of protective equipment emerging in railway in recent years. Nestor rolling cage is connected by Nestor connecting clip on the longitudinal tensile rib fixed on the bracket. The longitudinal tension and the support are connected with the Φ2.5mm cold-drawn galvanized steel wire around 2 laps and then tightened. The support is set in the column and the middle of the span of the protective fence of 3m. The other spans are only set with the upper column, and the support and the protective fence are connected with the bracket hoop. For the protective fence that has been installed with metal mesh, the Nestor roller cage is directly fixed on the transverse sheet and wire of the metal mesh with the cold-drawn galvanized steel wire of 2.5mm or the Nestor connection fastener.

The quality of hot-dip galvanized barbed wire is only good in the surface of the wire attached to the galvanized layer, and with the chemical reaction, the surface of the zinc layer will gradually lose effect because of the oxidation reaction, this situation is more prominent in the humid area of the environment. And because after all, it is rusty iron wire, so the quality of hot-dip galvanized barbed rope is certainly not up to the level of stainless steel barbed rope.

The construction of inner wall and outer wall steel wire mesh can effectively solve the wall cracks, falling off, empty drum phenomenon. Hot dip galvanized steel wire mesh material requirements: net surface leveling, width and length to meet the project required standards, welding process, weight, zinc, etc., with more production and operation, detection certificate is complete.

The management system of the rinsing water after the steel wire pickling should be regularly and regularly discharged after the rinsing water, and the rinsing water should be kept clean and low acid value as far as possible. The pH control is more appropriate. The concentration of plating aid should not be too high. Hot plating wire must be added ammonium chloride and zinc chloride according to the data of laboratory analysis, and the specific gravity of the composite solution is controlled in the range of 50~80g/L. The addition of ammonium chloride or zinc chloride raw materials without the results of laboratory analysis shall be subject to criticism and education, and economic treatment if necessary.