The barbed rope produced by the barbed rope factory adopts the way of winding in order to facilitate transportation, and the disk weight of the galvanized barbed rope is different according to the size.
- In use, it can be well used to control the degree of softness and hardness in the annealing process, mainly used for binding silk and binding wire in the construction industry. Its use is not limited to handicrafts, of course, in the construction industry is also widely used. In the early days, the lanterns were made with wire outside and proper candles were placed inside. People hung them in front of the door and it was very beautiful to go up at night.
- Under normal circumstances, the organic matter contained in galvanized wire can make electroplating speed significantly reduced. Although chemical formulations facilitate high deposition rates, the deposition of organic matter does not meet the requirements of coating thickness, so activated carbon can be used to treat the bath.
Post time: 16-03-23There are two kinds of use, namely slope protection hook mesh, coal hook mesh, mining hook mesh, coal mine support network, roadway support network. The height of the outer rail of the pavement or seat belt should not be less than 1.10 m. The net distance between balustrade members shall not be greater than 140 mm, and horizontal rail shall not be used. Hook mesh planning is necessary to be safe and reliable, anchor should be installed on the basis of the railings, its strength should meet the requirements of the standard.
Large coil galvanized wire in the zinc immersion distance debugging, keep the original speed unchanged, according to t= KD to determine the zinc immersion time (1), where: t is the zinc immersion time is constant, take 4-7D is the diameter of steel wire mm, and then estimate the zinc immersion distance. By adjusting the zinc dip distance, the zinc dip time of steel wire of various specifications can be shortened by 5s on average. In this way, the zinc consumption per ton of steel wire decreases from 61kg to 59.4kg.
- The disposal characteristics and advantages of galvanized hook net, two kinds of disposal methods of galvanizing: cold plating and hot plating, are better than the anticorrosion corrosion prevention and rust prevention disposal of dip plastic, so the service life is much longer than the dip plastic hook net. Full cover galvanized can also control the cost of consumption, stop a large range of large quantities of galvanized.
According to the different requirements of the industry, in accordance with the standard allocation in the smelting furnace, put the different weight of alloy ingots, such as weaving, Ming, paper, lang, silicon, etc., this kind of smelting out of the data is called gold ore iron. Iron has gray iron, white iron and the above-mentioned gold, they have different characteristics, so in the industry according to their different characteristics to transport and selection.
Some customers are just for ordinary fencing, but the pictures provided to the barbed rope factory are indeed applied to the barbed rope products in prison, maybe because the customers prefer the style, but such products are really a little overqualified to be installed in ordinary areas. Even if the customers prefer such barbed rope products, the higher price is prohibitive. The price and quality of the prison rope are certainly not the level of the rope we contact in our daily life.
- It helps to dissipate heat. Building grid (floor heating) has good thermal conductivity and heat dissipation, the appearance of heat dissipation effect is more average 2 cm, 2.5 cm, 5 cm, 10 cm, 15 cm, 20 cm. Wire rope thickness, net length, net width, mesh and other indicators can be stopped at any time according to customer request. The mesh, solder joints, and mesh are all equal.
Post time: 22-12-22There is also a scaly or boride film or oxide. To remove the photosynovium or oxide commonly used methods are: lead grease removal method, acoustic cleaning method, alkali washing or pickling electrolysis grease to oxide method, these methods in the use of gas or steam harmful to human body, pollution, not environmental protection.
2. Adjust the drawing process parameters of the water tank
But there are some necessary precautions in the production of galvanized wire. Remove all tools and piles on the work site and equipment that hinder activities, and slowly put the wire into the cylinder during pickling to prevent acid splashing on the body. When adding acid, the acid must be slowly poured into the water. Do not pour water into the acid to prevent acid spillage and injury. Workers should wear protective glasses when working. Then in the handling of wire and other items, it is strictly prohibited to push hard.
Post time: 23-03-23No matter how good the quality of hot-dip galvanized barbed rope is, it is only attached to the surface of the wire with galvanized layer, and with the cause of chemical reaction, the zinc layer on the surface will gradually lose its effect because of oxidation reaction, which is more prominent in the humid area of the environment. And because, after all, the wire will rust, so the quality of hot-dip galvanized barbed rope is certainly not up to the level of stainless steel barbed rope.
- The coating on the surface of the welding core is called the coating. The coating of electrode plays a very important role in the welding process. If the photoelectrode without drug skin is used for welding, in the welding process, oxygen and nitrogen in the air will invade a large number of molten metal, metal iron and beneficial elements such as carbon, silicon, manganese oxidation and nitriding to form various oxides and nitrides, and residual in the weld, resulting in slag inclusion or cracks in the weld. The gas in the weld pool may produce a large number of pores in the weld. These factors can greatly reduce the mechanical properties of the weld and make it brittle.
There are many kinds of specifications for crack resistant welding mesh used in the construction industry. The commonly used specifications are as follows:
Zinc is a silver-white metal, brittle at room temperature, soluble in acid can also be soluble in alkali, known as amphoteric metal. Pure zinc in dry air is more stable, in humid air or containing carbon dioxide and oxygen water is small, the surface will generate a layer of basic zinc carbonate based thin film layer, it can delay the corrosion rate of zinc layer. The corrosion resistance of zinc coating in aqueous solution of acid, alkali and sodium chloride is stronger.
Post time: 09-06-22Hot – plated wire average performance: reflected in its cross – section, longitudinal uniformity. In the actual process of operation, such as steel wire jitter, the surface scum plating pot and other reasons will cause the surface of galvanized wire galvanized layer accumulation, should strive to solve the problem. In addition to these reasons, we should pay attention to the tooling and process must be stable, and regular testing should be done to ensure the uniformity of the galvanized layer.
Galvanized iron wire is a substance we often see in life. It is the zinc gradually plated on the metal surface through the unidirectional current in the electroplating tank. The production speed is slow, the coating is uniform, the thickness is thin, usually only 3-15 microns, the appearance is bright, the corrosion resistance is poor, and the corrosion will rust in a few months. Galvanized wire has the characteristics of thick galvanized layer, strong corrosion resistance, strong galvanized layer, etc., the products are widely used in construction, highway walls, Zahua, weaving nets.
The national standard on the use of wire mesh standards have certain requirements, diameter and mesh size matching use, rather than simply diameter size, on the plaster layer to use is mesh should not be greater than 20×20, diameter is not easy to be less than 1mm, light selection diameter is not much significance, choose 40×40×0.9 and choose 10×10×0.6 wire mesh, Which is better, I’m afraid is 10×10×0.6.
Post time: 06-05-22
Post time: 07-11-22
Raw material of wire mesh sheet cold drawn low carbon steel wire base material can choose low carbon steel hot rolled disk bar or hot rolled smooth steel bar. The base material number and diameter of cold-drawn low carbon steel wire can be confirmed according to the rules in the table below. During the cold drawing process, the surface shrinkage rate of each drawing should not be greater than the wire mesh before cold drawing. Annealing shall not be carried out during wire drawing. If butt welding is required, the same production unit and base material of the same number should be selected. The appearance quality of wire mesh should not affect wire drawing. When the welding function is poor or brittle fracture occurs, special inspection should be carried out according to relevant standards.