compresores diésel de arena


(1) If the horizontal slurry pump causes a blockage of solid hard deposits in the volute, measures can be taken to remove the blockage.
(2) If the shaft is different from the stuffing box axis, it is mainly due to processing errors and incorrect installation. Then pay attention to check whether the installation is correct after installation. If the sealing water ring is badly worn, a new water ring needs to be replaced. If the sealing water pipe is blocked, the sealing water cannot enter the middle of the packing, resulting in rapid wear of the packing, resulting in material leakage, you should dredge the blocked water pipe and keep the sealing water clean.
(3) If the impeller or the inlet and outlet water pipe is blocked, the impeller or pipe can be cleaned, and if the impeller is seriously worn, it should be replaced. If the filler mouth leaks, press the filler. If the conveying height is too high or the tube loss resistance is too large, the conveying height should be reduced or the resistance reduced.

...

In conclusion, manganese plays a pivotal role in the manufacturing of jaw plates for crushers in the mining industry. Its unique properties enhance the performance and longevity of these critical components, thereby contributing to the efficiency and cost-effectiveness of mining operations. As the industry evolves, ongoing innovations in material science promise to further improve the effectiveness of manganese jaw plates, ensuring they remain a vital element in the world of mining and crushing.


...

  • 1.The selection of the pump is too large, and the flow and head are larger than the actual condition due to improper selection of the coefficient. This situation makes the pump in the operation process, cavitation phenomenon, resulting in premature damage of the pump flow parts under the combined action of cavitation and abrasion, in the case of serious cavitation, the pump will produce vibration and noise, and even lead to a sharp decline in the flow, head and efficiency of the pump can not run; In addition, the pump in the operation of large flow, will also cause motor overload, heat, serious will burn the motor.
  • ...


    (1) When using the drilling rig to drill, the driver should be placed in the drilling position, so that the front end is against the rock, and the distribution should be careful to let the drilling rig move forward, so that the drill bit touches the rock; When opening the hole, first quietly let the drilling rig drive, when the drill rod is in place in the rock, it is allocated to the full open position.
    (2) Before starting the drilling rig, check whether the charging pressure of the accumulator is normal; Check whether the scouring water pressure and the lubricating air pressure can be; Check whether there is sufficient lubricating oil in the lubricator, and whether the oil supply is appropriate; Check the reverse tendency of the oil pump motor. (3) If the drilling rig cannot open the hole smoothly, it should first assign the rock drill to retreat, and then let the rock drill move forward to open the hole from the beginning.
    (4) When replacing the drill bit, the drill bit should be gently pressed against the rock, so that the motor of the drill can be reversed to complete the sensitive unloading head.
    (5) The inspection of hydraulic components can only be prevented under the condition of pole cleaning, and after the connecting tissue is removed, it must be quickly plugged with the cleaning tightly matched plug. Before the repaired rock drill is used from scratch, it is necessary to circulate the hydraulic oil into the oil circuit to wash the components of the hydraulic system.
    (6) The oil level and oil supply of the lubricator should be checked regularly; The gear with reverse structure is regularly filled with high-temperature grease; Check the oil level in the lubricating oil tank regularly and remove the dirt in the oil tank

    ...


    2). Features:
    1, the drill selects the motor through the high-performance reducer as the reverse power; Use cylinders for propulsion. The hydraulic system is eliminated, so the mechanical efficiency is high, the cost is low, and the performance is stable.2, with anti-card maintenance, when the drill is stuck, the motor is not easy to burn, the reducer is not easy to damage.
    3, simple and easy to move, the weight of the drill machine is less than 500Kg, and can be broken down into three pieces, easy to move and put on the shelf.
    4, the selection of rolling drag plate, the track is not easy to wear.
    5, the drilling machine uses semi-automatic cloud dynamic disassembling drill pipe, high efficiency.

    ...